Proxmark3 community

Research, development and trades concerning the powerful Proxmark3 device.

Remember; sharing is caring. Bring something back to the community.


"Learn the tools of the trade the hard way." +Fravia

You are not logged in.

Announcement

Time changes and with it the technology
Proxmark3 @ discord

Users of this forum, please be aware that information stored on this site is not private.

#1 2022-05-21 21:34:31

ryanr775
Contributor
Registered: 2020-11-10
Posts: 5

PM3 Will not read cards anymore

RDV4 -
PM3 fails to initialize and parse data on a card, below example has no card anywhere near the device for both lf and hf searches, both fail with a card either way. Operating latest version and cannot seem to get a solution to this through the other issue requests I've found online. Worked fine untouched up until about last week, since then I have reflashed the hardware 5 or 6 times, both macOS and windows, using different cables, and have found no solution to my issue.

This occurs when running lf search, hf search, or any code that would require communicating with the device as far as I can tell.

HW ver, HW status, data tune:

[ Proxmark3 RFID instrument ]

[ CLIENT ]
Iceman/master/v4.14831-555-gad79e8433 2022-04-28 22:34:22 f194e98b6
compiled with............. Clang/LLVM Apple LLVM 13.1.6 (clang-1316.0.21.2.3)
platform.................. OSX / x86_64
Readline support.......... present
QT GUI support............ present
native BT support......... absent
Python script support..... absent
Lua SWIG support.......... present
Python SWIG support....... absent

[ PROXMARK3 ]

hw status
[usb] pm3 --> hw status
[!!] ? UART:: write time-out
[!] ⚠️ Status command timeout. Communication speed test timed out
data tune
[usb] pm3 --> data tune
[=] ---------- Reminder ------------------------
[=] hw tune doesn't actively tune your antennas,
[=] it's only informative.
[=] Measuring antenna characteristics, please wait...
? 20[!!] ? UART:: write time-out
? 0
[!] ⚠️ No response from Proxmark3. Aborting...


HW Ver:
[usb] pm3 --> hw ver

[ Proxmark3 RFID instrument ]

[ CLIENT ]
Iceman/master/v4.14831-555-gad79e8433 2022-04-28 22:34:22 f194e98b6
compiled with............. Clang/LLVM Apple LLVM 13.1.6 (clang-1316.0.21.2.3)
platform.................. OSX / x86_64
Readline support.......... present
QT GUI support............ present
native BT support......... absent
Python script support..... absent
Lua SWIG support.......... present
Python SWIG support....... absent

[ PROXMARK3 ]
device.................... RDV4
firmware.................. RDV4
external flash............ present
smartcard reader.......... present
FPC USART for BT add-on... absent

[ ARM ]
bootrom: Iceman/master/v4.14831-555-gad79e8433 2022-04-28 22:33:29 f194e98b6
os: Iceman/master/v4.14831-555-gad79e8433 2022-04-28 22:33:51 f194e98b6
compiled with GCC 10.2.1 20201103 (release)

[ FPGA ]
LF image 2s30vq100 2022-03-23 17:21:05
HF image 2s30vq100 2022-03-23 17:21:16
HF FeliCa image 2s30vq100 2022-03-23 17:21:27
HF 15 image 2s30vq100 2022-03-23 17:21:38

[ Hardware ]
--= uC: AT91SAM7S512 Rev A
--= Embedded Processor: ARM7TDMI
--= Internal SRAM size: 64K bytes
--= Architecture identifier: AT91SAM7Sxx Series
--= Embedded flash memory 512K bytes ( 64% used )


Example of issue:
[usb] pm3 --> lf sea
[=] You can cancel this operation by pressing the pm3 button
[!] ⚠️ (lf_read) command execution time out
[-] ⛔ Data in Graphbuffer was too small.
[usb] pm3 --> hf sea
? Searching for ThinFilm tag...[!] ⚠️ timeout while waiting for reply.
? Searching for iCLASS / PicoPass tag...
[+] Valid iCLASS tag / PicoPass tag found

? Searching for FeliCa tag...
[+] Valid ISO 18092 / FeliCa tag found

[usb] pm3 -->
(There was not a valid card on the scanner when hf search was run.

Would appreciate any assistance you can provide. I made an issue request on the GitHub but we were unable to figure it out there.
(https://github.com/RfidResearchGroup/proxmark3/issues/1667)

Offline

Board footer

Powered by FluxBB