Proxmark3 community
Research, development and trades concerning the powerful Proxmark3 device.
Remember; sharing is caring. Bring something back to the community.
"Learn the tools of the trade the hard way." +Fravia
You are not logged in.
Announcement
Time changes and with it the technology
Proxmark3 @ discord
Users of this forum, please be aware that information stored on this site is not private.
#1 2017-06-09 09:07:42
- Dot.Com
- Contributor
- From: Hong Kong
- Registered: 2016-10-05
- Posts: 180
- Website
Replicate Elechouse Pm3 Easy and Real Elechouse Pm3 Easy
I got a lot of feedbacks via my website about low-quality pm3 and even some china sellers are approaching me to sell their pm3 easy at a lower rate on my website. I strongly advise people to take a look at the pm3 below.
Please note on this.
(Non-Original) Look at the font to be sure. Very ugly :X
Non-Original normally comes in a box of being assembled already.
(Original) Loaded with 2.0.0 Look at the font. Printed nicely.
The original will only come in parts that require you to assemble on your own.
Just a short guide for people buying pm3.
Last edited by Dot.Com (2017-06-09 13:32:31)
Offline
#2 2017-06-09 09:18:27
- iceman
- Administrator
- Registered: 2013-04-25
- Posts: 9,537
- Website
Re: Replicate Elechouse Pm3 Easy and Real Elechouse Pm3 Easy
There is always a risk with buying Alibaba or on Taobao, if the price is dirtcheap then there is a reason for it...
Offline
#3 2017-06-11 14:04:53
- lenny
- Contributor
- Registered: 2017-05-28
- Posts: 4
Re: Replicate Elechouse Pm3 Easy and Real Elechouse Pm3 Easy
I got a fake board (ebay), I wouldn't say it was 'dirt cheap' either...
The listing pictured both genuine unboxed Elechouse and the fake pre-assembled Elechouse in box, but instead I got the half-horse chinese branded board with the little picture of a hand and card on the middle board, no box. The seller didn't even try.
Do you know what issues the fakes have?
It seems to (very slowly) produce working viking clones, but it would be a shame if it was missing some of the other exciting stuff the Elechouse 'Easy' has. I don't have a genuine board to compare.
(Also still curious to know what the RDV2 version can do that the 'Easy' can't, if anyone can tell me this.)
Offline
#4 2017-06-12 05:13:02
- Dot.Com
- Contributor
- From: Hong Kong
- Registered: 2016-10-05
- Posts: 180
- Website
Re: Replicate Elechouse Pm3 Easy and Real Elechouse Pm3 Easy
I have both proxmark3 easy and proxmark rdv2.
Correct me if i am wrong.
I used the rdv2 to sniff iclass keys worked really well. Pm3 Easy was giving me lots of issues on this.
1) my guess is the easy is more for cloning purposes
the voltage for HF on rdv2 are much stronger, LF stays strong always.
Easy has a low voltage for HF, LF fluctuates pretty badly. sometimes at 10, sometimes at 20, sometimes at 40.
2) Voltage
legic read on hf will definitely be easy on rdv2 as it only reads up to 0.5cm~. while you have to flip and remove the LF antenna to do so for legic.
3) reading of legic
I am not too sure about the rest. All my explanation is based on my experience. No offense if I am wrong.
Offline