Proxmark developers community

Research, development and trades concerning the powerful Proxmark3 device.

Remember; sharing is caring. Bring something back to the community.


"Learn the tools of the trade the hard way." +Fravia

You are not logged in.

#1 2017-09-13 03:04:32

newcomer
Contributor
Registered: 2017-09-13
Posts: 8

need your help?pm3 --> hf emv trans #db# unknown command:: 0x0701

pm3 --> hw
help             This help         
detectreader     ['l'|'h'] -- Detect external reader field (option 'l' or 'h' to limit to LF or HF)         
fpgaoff          Set FPGA off         
lcd              <HEX command> <count> -- Send command/data to LCD         
lcdreset         Hardware reset LCD         
readmem          [address] -- Read memory at decimal address from flash         
reset            Reset the Proxmark3         
setlfdivisor     <19 - 255> -- Drive LF antenna at 12Mhz/(divisor+1)         
setmux           <loraw|hiraw|lopkd|hipkd> -- Set the ADC mux to a specific value         
tune             Measure antenna tuning         
version          Show version information about the connected Proxmark         
status           Show runtime status information about the connected Proxmark         
ping             Test if the pm3 is responsive         
pm3 --> hf
help             This help         
14a              { ISO14443A RFIDs... }         
14b              { ISO14443B RFIDs... }         
15               { ISO15693 RFIDs... }         
epa              { German Identification Card... }         
emv              { EMV RFIDs... }         
legic            { LEGIC RFIDs... }         
iclass           { ICLASS RFIDs... }         
mf               { MIFARE RFIDs... }         
mfu              { MIFARE Ultralight RFIDs... }         
mfdes            { MIFARE Desfire RFIDs... }         
topaz            { TOPAZ (NFC Type 1) RFIDs... }         
tune             Continuously measure HF antenna tuning         
list             List protocol data in trace buffer         
search           Search for known HF tags [preliminary]         
snoop            <samples to skip (10000)> <triggers to skip (1)> Generic LF/HF Snoop in Testing stage 
pm3 --> hf search
         
UID : 4F 6A CF 9A           
ATQA : 00 04         
SAK : 28 [1]         
TYPE : JCOP31 or JCOP41 v2.3.1         
ATS : 07 78 B3 B4 02 47 44 A8 4E           
       -  TL : length is 7 bytes         
       -  T0 : TA1 is present, TB1 is present, TC1 is present, FSCI is 8 (FSC = 256)         
       - TA1 : different divisors are NOT supported, DR: [2, 4], DS: [2, 4]         
       - TB1 : SFGI = 4 (SFGT = 65536/fc), FWI = 11 (FWT = 8388608/fc)         
       - TC1 : NAD is NOT supported, CID is supported         
       -  HB : 47 44           
Answers to magic commands (GEN1): NO         

Valid ISO14443-A Tag Found - Quiting Search
         
pm3 --> hf emv
help             This help         
trans            Perform EMV Reader Transaction         
getrng           get random number from terminal         
eload            load EMV tag into device         
dump             Dump EMV tag values         
list             [Deprecated] List ISO7816 history
pm3 --> hf emv trans
#db# unknown command:: 0x0701

Offline

#2 2017-09-13 04:56:12

iceman
Administrator
Registered: 2013-04-25
Posts: 4,070
Website

Re: need your help?pm3 --> hf emv trans #db# unknown command:: 0x0701

Welcome and I suggest you read http://www.proxmark.org/forum/viewtopic.php?id=1125 as an introduction.

This is the introduction section,  you can now post the rest of the forum.


modhex(hkhehghthbhudcfcdchkigiehgduiehg)

Offline

#3 2017-09-13 07:03:33

newcomer
Contributor
Registered: 2017-09-13
Posts: 8

Re: need your help?pm3 --> hf emv trans #db# unknown command:: 0x0701

i've got it,thanks。

Offline

Board footer

Powered by FluxBB