Research, development and trades concerning the powerful Proxmark3 device.
Remember; sharing is caring. Bring something back to the community.
"Learn the tools of the trade the hard way." +Fravia
You are not logged in.
Time changes and with it the technology
Proxmark3 @ discord
Users of this forum, please be aware that information stored on this site is not private.
lf t55 det wont work, and Ive tried a few modulations but cannot wipe, clone or write to this tag.
Heres a link to the data file.
https://www.dropbox.com/s/7rzusg2ta00lxbs/buttonT55.pm3?dl=0
Last edited by Apt-Get (2016-01-27 00:59:46)
Offline
Looks like its ASK/32/inverted also with a STT.
You should be able to use the "lf t55xx" commands with that config.
Offline
proxmark3> lf t55 conf i 1
Chip Type : T55x7
Modulation : ASK
Bit Rate : 2 - RF/32
Inverted : Yes
Offset : 0
Block0 : 0x00000000
proxmark3> lf t55 dump
Reading Page 0:
blk | hex data | binary
----+----------+---------------------------------
#db# DownloadFPGA(len: 42096)
0 | 00000000 | 00000000000000000000000000000000
1 | 00000000 | 00000000000000000000000000000000
2 | 00000000 | 00000000000000000000000000000000
3 | 00000000 | 00000000000000000000000000000000
4 | 00000000 | 00000000000000000000000000000000
5 | 00000000 | 00000000000000000000000000000000
6 | 00000000 | 00000000000000000000000000000000
7 | 00000000 | 00000000000000000000000000000000
Reading Page 1:
blk | hex data | binary
----+----------+---------------------------------
0 | 00000000 | 00000000000000000000000000000000
1 | 00000000 | 00000000000000000000000000000000
2 | 00000000 | 00000000000000000000000000000000
3 | 00000000 | 00000000000000000000000000000000
proxmark3> lf t55 wipe
Beginning Wipe of a T55xx tag (assuming the tag is not password protected)
Writing page 0 block: 00 data: 0x00088040 pwd: 0x00000000
Writing page 0 block: 01 data: 0x00000000
Writing page 0 block: 02 data: 0x00000000
Writing page 0 block: 03 data: 0x00000000
Writing page 0 block: 04 data: 0x00000000
Writing page 0 block: 05 data: 0x00000000
Writing page 0 block: 06 data: 0x00000000
Writing page 0 block: 07 data: 0x00000000
proxmark3> lf t55 read b 0
Reading Page 0:
blk | hex data | binary
----+----------+---------------------------------
0 | 00000000 | 00000000000000000000000000000000
Still cannot write. I tried offset 1,3 33,30 also.
Last edited by Apt-Get (2016-01-27 01:49:09)
Offline
Any ideas? i cant write to these tags. What is STT? do I need to do something different fro my writes?
Last edited by Apt-Get (2016-01-27 02:38:00)
Offline
Could I ask what you want to do with this tag? What modulation type, what data you write into it?
I wonder about that value at the line
"Writing page 0 block: 00 data: 0x00088040 pwd: 0x00000000" that could not be the result of this "lf t55 wipe". Where did you find this wipe command? The question is because the value for block 0 "0x00088040" was mentioned from GO_TUS, it was in an write experiment on AT55x7 with an AM modulation, and with only 2 block of data ...
Here how could you be shure that this is AT55x7. When there are also AT5567 and 5577? When you set that config 0x00088040 with the first write command then write all the 7 data blocks, so we assuming the chip is very independent. It may not be good at all
I understood from Marshmellow and Iceman support, they mentioned in one place (I could not remember where) reset AT55x7 config by7 just overwriting what ever on any AT55x7 chip,
' Just write the block 0 all to 0' which means 'lf at55 wr b 0 d 00000000' you must not use even with the password.
Have you tried just that? only that one line.
Offline
Could I ask what you want to do with this tag? What modulation type, what data you write into it?
I wonder about that value at the line
"Writing page 0 block: 00 data: 0x00088040 pwd: 0x00000000" that could not be the result of this "lf t55 wipe". Where did you find this wipe command? The question is because the value for block 0 "0x00088040" was mentioned from GO_TUS, it was in an write experiment on AT55x7 with an AM modulation, and with only 2 block of data ...Here how could you be sure that this is AT55x7. When there are also AT5567 and 5577? When you set that config 0x00088040 with the first write command then write all the 7 data blocks, so we assuming the chip is very independent. It may not be good at all
I understood from Marshmellow and Iceman support, they mentioned in one place (I could not remember where) reset AT55x7 config by7 just overwriting what ever on any AT55x7 chip,
' Just write the block 0 all to 0' which means 'lf at55 wr b 0 d 00000000' you must not use even with the password.
Have you tried just that? only that one line.
Offline
Sorry my mistake the command line is
"lf t55xx wr b 0 d 00000000". NOT "lf at55xx wr b 0 d 00000000".
Somehow forum does not let me edit my post.
Offline
Sorry my mistake the command line is
"lf t55xx wr b 0 d 00000000". NOT "lf at55xx wr b 0 d 00000000".Somehow forum does not let me edit my post.
Yes tried all these. From Icemans Suggestion.
- try first
lf t55xx write b 0 d 00088040
--test with
lf t55 detect
- try second.
lf t55xx write b 0 d 00088040 p 00000000
lf t55 detect
lf t55xx write b 0 d 00088040 p ffffffff
lf t55 detect
Still nothing. no Writes. no t55 detect.
I think my problem lies in the modulation??
Offline
Problem likely lies in a large antenna vs small chip, it can cause problems if the antenna and tag size are not tuned.
Oh and do not write a block 0 of 00000000 it will make your tag go crazy. It is NOT a valid config block setting.
Offline
anything i can do to tune this Marshmellow? im running a pm3 v2
bootrom: /-suspect 2015-11-04 22:15:34
os: master/v1.1.0-657-gc4c3af7-suspect 2016-01-26 07:48:55
LF FPGA image built for 2s30vq100 on 2015/03/06 at 07:38:04
HF FPGA image built for 2s30vq100 on 2015/11/ 2 at 9: 8: 8
# LF antenna: 45.10 V @ 125.00 kHz
# LF antenna: 20.35 V @ 134.00 kHz
# LF optimal: 46.20 V @ 123.71 kHz
# HF antenna: 28.75 V @ 13.56 MHz
Displaying LF tuning graph. Divisor 89 is 134khz, 95 is 125khz.
Offline
Could you try with these
lf t55xx wr b 0 d 00088040
lf t55xx wr b 1 d D1063838
lf t55xx wr b 2 d 7C800001
then try the lf t55 commands again.
resumee:
this is ASK, 2 data blocks config. We set the config, then we give the fob exact the data it should have been configured to contain. With that we construct a clean situation, the lf t55 commands should report cleanly back, as expected.
(I wish I could understand what is in b1 and b2??? where can we have info what is in those blocks and how to decode it)
Last edited by M&S (2016-01-27 04:34:53)
Offline
you have a very strong antenna. Could you have problem when writing?
Also something is not right: Your divisor is 89 !
Last edited by M&S (2016-01-27 04:27:13)
Offline
you have a very strong antenna. Could you have problem when writing?
Also something is not right: Your divisor is 89 !
Heres what i found out..
http://www.proxmark.org/forum/viewtopic.php?pid=19715#p19715
Offline
Are these foam shrouded?
Offline
Are these foam shrouded?
no, thick hard plastic. smaller than a dime About the size of a mexican 5cent
I am able to read a write to these no problem Turns out my antenna was too strong for reliable detects and writes.
Once i brought the voltage down to 35 its working perfect on all t5577 that i have tried.
Thanks again to @Marshmellow for the Tip.
Last edited by Apt-Get (2016-01-27 20:22:46)
Offline