Proxmark3 community

skappy

Contributor

Registered: 2014-01-13

Posts: 91

Need your help concerning 0x0613 error please ...

Dear all,

I'm working under the Icemandocker system ( V1.6.6), ./start.sh have been launched  and I would like to run a hardnested operation  but i'm encountering some difficulties, operation end with an 0x0613 error ... May I ask you help please ?
Thank you very much for your help ,

Here is the screen copy

I have a PM3 from Elechouse with the following characterisitics :

pm3 --> hw version
[[[ Cached information ]]]

Prox/RFID mark3 RFID instrument
bootrom: /-suspect 2015-11-19 10:08:02
os: /-suspect 2015-11-19 10:08:09
LF FPGA image built for 2s30vq100 on 2015/03/06 at 07:38:04
HF FPGA image built for 2s30vq100 on 2015/11/ 2 at  9: 8: 8

uC: AT91SAM7S512 Rev A
Embedded Processor: ARM7TDMI
Nonvolatile Program Memory Size: 512K bytes. Used: 169916 bytes (32%). Free: 354
372 bytes (68%).
Second Nonvolatile Program Memory Size: None
Internal SRAM Size: 64K bytes
Architecture Identifier: AT91SAM7Sxx Series
Nonvolatile Program Memory Type: Embedded Flash Memory

pm3 -->

pm3 --> hf list 14a
Recorded Activity (TraceLen = 188 bytes)

Start = Start of Start Bit, End = End of last modulation. Src = Source of Trans
er
iso14443a - All times are in carrier periods (1/13.56Mhz)
iClass    - Timings are not as accurate

      Start |        End | Src | Data (! denotes parity error)
                 | CRC | Annotation         |
------------|------------|-----|-----------------------------------------------
-----------------|-----|--------------------|
          0 |        992 | Rdr |52
                 |     | WUPA
       2244 |       4612 | Tag |04  00
                 |     |
       7040 |       9504 | Rdr |93  20
                 |     | ANTICOLL
      10692 |      16580 | Tag |23  3d  84  86  1c
                 |     |
      18688 |      29216 | Rdr |93  70  23  3d  84  86  1c  c0  0e
                 |  ok | SELECT_UID
      30404 |      33924 | Tag |08  b6  dd
                 |     |
      35456 |      40224 | Rdr |60  02  e7  58
                 |  ok | AUTH-A(2)
      44996 |      49732 | Tag |b0  f0  0a  04
                 |     |
      58496 |      67808 | Rdr |87  81! 34  7a! 0f  6a! c2  5e!
                 | !crc| ?
      69060 |      73796 | Tag |af  e5! 2e  04
                 |     |
      79232 |      83936 | Rdr |36  14  19  25!
                 | !crc| ?
      85188 |     106052 | Tag |de  d4  90  be  78  60! 7f  eb  f6! f7  65  b6!
4c! 02  a7  f3   |     |
            |            |     |27  b0
                 | !crc|
     118144 |     122912 | Rdr |22! 79  6e! ec
                 | !crc| ?
pm3 -->

pm3 --> hf mf hardnested 3 A ffffffffffff 4 A w
--target block no:  4, target key type:A, known target key: 0x000000000000 (not
set), file action: write, Slow: No, Tests: 0
Allocating memory for partial statelists...
Generating partial statelists...
Generating bitflip statelist...
Acquiring nonces...
#db# unknown command:: 0x0613
Waiting for a response from the proxmark...
Don't forget to cancel its operation first by pressing on the button
Error: No response from Proxmark.

pm3 -->

iceman

Administrator

Registered: 2013-04-25

Posts: 9,538

Website

Re: Need your help concerning 0x0613 error please ...

I'm guessing you didn't flash your device with v1.6.6 firmware before running the client.

skappy

Contributor

Registered: 2014-01-13

Posts: 91

Re: Need your help concerning 0x0613 error please ...

Dear Iceman,
May i ask you help concerning this flashing step please ?
I have follow the indications under your public repository for flashing the PM3, that is to say

To flash
client/flasher /dev/ttyACM0 armsrc/obj/fullimage.elf
--> keeps waiting for device to come back online. press CTRL-C
mknod /dev/ttyACM0 c 166 0
client/flasher /dev/ttyACM0 armsrc/obj/fullimage.elf
mknod /dev/ttyACM0 c 166 0

Run the PM3 client:
cd client
./proxmark3 /dev/ttyACM0

and finally obtain

Prox/RFID mark3 RFID instrument
bootrom: /-suspect 2015-11-19 10:08:02
os: /-suspect 2015-11-19 10:08:09
LF FPGA image built for 2s30vq100 on 2015/03/06 at 07:38:04
HF FPGA image built for 2s30vq100 on 2015/11/ 2 at  9: 8: 8

Have I done something wrong ?

Thank you for your help Iceman,

Have a great day

iceman

Administrator

Registered: 2013-04-25

Posts: 9,538

Website

Re: Need your help concerning 0x0613 error please ...

What is the output from the above commands?

skappy

Contributor

Registered: 2014-01-13

Posts: 91

Re: Need your help concerning 0x0613 error please ...

Dear Iceman ,

you were absolutely right ...

Things are running nicely now

Thank for being there and also thanks and congratulation for all the job you are doing around Docker ...

Have a nice day

Skappy