Research, development and trades concerning the powerful Proxmark3 device.
Remember; sharing is caring. Bring something back to the community.
"Learn the tools of the trade the hard way." +Fravia
You are not logged in.
Time changes and with it the technology
Proxmark3 @ discord
Users of this forum, please be aware that information stored on this site is not private.
Pages: 1
Hi,
I try it command lf t55xx detect
Chip Type : T55x7
Modulation : DIRECT/NRZ
Bit Rate : 1 - RF/16
Inverted : No
Offset : 47
Seq. Term. : No
Block0 : 0x00040000
because lf search u not working.
I also try it lf t55xx dump
Reading Page 0:
blk | hex data | binary
----+----------+---------------------------------
0 | 00040000 | 00000000000001000000000000000000
1 | 00100000 | 00000000000100000000000000000000
2 | 00000000 | 00000000000000000000000000000000
3 | 00400000 | 00000000010000000000000000000000
4 | 00100000 | 00000000000100000000000000000000
5 | 00400000 | 00000000010000000000000000000000
6 | 00400000 | 00000000010000000000000000000000
7 | 01000000 | 00000001000000000000000000000000
Reading Page 1:
blk | hex data | binary
----+----------+---------------------------------
0 | FFFFFFFF | 11111111111111111111111111111111
1 | FFFFFFFF | 11111111111111111111111111111111
2 | 00000000 | 00000000000000000000000000000000
3 | 01000000 | 00000001000000000000000000000000
How can I get command for clone ? Or How can I decrypt it ?
Thank you so much !!
Offline
while it says NRZ, then config looks very blank for a t55xx.
Maybe perform and
lf read
data save filename.pm3
and share via a file sharing service and post a link to it.
edit: as per icemans request.
Last edited by mwalker (2019-11-05 00:25:58)
Offline
..maybe incurage ppl to use filesharing services ?
Offline
Hi, very thanks for your time. Maybe see as blank but I think it´s one of first chip here on the system. Maybe have easy to remember code.
File is here https://we.tl/t-z5SgP72yQl
I hope I used the right service you wanted.
Thanks
Martin
Offline
Do you have any idea how to clone this chip?
Thanks for your time
Offline
The data in the file is very week. I would like to see a much stronger signal.
Offline
Here is new data. Please try it or tell me how can I get it better data (signal).
https://wetransfer.com/downloads/cf188318cec615f5a0863cb4d3cb315220191111082132/d2f20562363f7e8d289f12e0f45b0c4920191111082132/380a81
Thanks
Martin
Offline
based on the data in the file(s) i am not sure its an lf/125 khz card.
It seems to be not much more then just noise (with no card on the reader)
Can post the results of the following with no card on the reader, then repeat but with the card on the reader.
hw tune
Offline
Here is new data:
1. without card LF
2. with card LF
3. without card HF
4. with card HF
https://wetransfer.com/downloads/32b816aa9df6edcd867292284e0c8bb920191113102748/b31df3d752ed6767215f0b4d3d10eba420191113102748/7cd355
And here is image from HW TUNE with LF antenna
https://imgur.com/a/5plBLbE
Offline
I will let the hardware guys comment more on this, but to me the hw tune voltages look low. And the HF looks like its antenna is not there.
hw tune with no tag (copied from the image so others can quickly see)
# LF antenna: 19.25 V @ 125.00 kHz
# LF antenna: 9.76 V @ 134.00 kHz
# LF optimal: 19.25 V @ 125.00 khz
# HF antenna: 0.81 V @ 13.56 Mhz
with tag
# LF antenna: 8.94 V @ 125.00 kHz
# LF antenna: 9.07 V @ 134.00 kHz
# LF optimal: 9.76 V @ 110.09 khz
# HF antenna: 0.85 V @ 13.56 Mhz
Is the device you are trying to read a full size card or a fob/tag ?
Offline
Looks like a decent antenna 19v, is this a RDV2 device? And the voltage drop indicates a good coupling. You shouldn't have any issues with it. The HF looks like its been disconnected, which is possible on a RDV2 with its individual cables.
Offline
thanks iceman, i guess I have gotten used to the RDV4 voltages, even my easy is 35V
The data files have very low readings, the first one was -2 to 2 (i.e. looked like nothing was on the antenna). the second one was a little better, but still very low. So I'm running out of ideas.
Offline
Thanks guys for your patient with me. So sorry for longer response.
So I have this device : https://imgur.com/a/FcPRo6B
From rysc corp, bought here: https://store.ryscc.com/products/new-proxmark3-kit
The device what I trying to read is fob tag, here is photo: https://imgur.com/a/NmKVvcf
On the door or toll-bar works fine.
Maybe there are problem with low energy my proxmark ?
Would it be better to buy a 35V device? (RDV4)
I am able to all solutions what do you suggest. Including the purchase of new equipment.
PS: You mean RDV4 this product? https://lab401.com/products/proxmark-3- … 8437911663
Offline
That looks like an old Motorola FlexPass tag. I recently added support for it over at the RRG/Iceman repo. I am very curious if the implementation can read it.
Your device is good enough. No need to spend 300 USD more.
Anyway, the tag explains the strange readings.
Offline
Pages: 1